Nissan L6 Forum

6886 topics in this forum

1. camshaft, long duration but low lift?

   By franky240z, September 25, 2012
   • 16 replies
   • 4.5k views
   • 
   • franky240z
   • September 30, 2012

3. Nissan H30 engine...

   By itsadatsun240z, September 20, 2012
   • 3 replies
   • 5.7k views
   • 
   • itsadatsun240z
   • September 30, 2012

4. 3.1 Stroker Pistons Recommendation

   By '71 GT2, September 25, 2012
   • 6 replies
   • 2k views
   • 
   • '71 GT2
   • September 28, 2012

5. bore for KA24E pistons

   By sotaorava, September 24, 2012
   • 1 reply
   • 1.4k views
   • 
   • ctc
   • September 24, 2012

6. Healthy Oil Pressure Range

   By TieFighter88, September 24, 2012
   • 1 reply
   • 757 views
   • 
   • OldAndyAndTheSea
   • September 24, 2012

7. L28ET Swap, Rich idle, lean under boost

   By ryan95i4, September 12, 2012
   • 17 replies
   • 3.5k views
   • 
   • ryan95i4
   • September 21, 2012

8. valve stem seal problem

   By skirkland1980, September 18, 2012
   • 9 replies
   • 1.5k views
   • 
   • NewZed
   • September 21, 2012

9. Head Gasket Question

   By shri2222, August 23, 2012
   • 7 replies
   • 2.9k views
   • 
   • steve260z
   • September 21, 2012

10. Installing used camshaft 1 2

    By SleeperZ, December 12, 2011
    • 23 replies
    • 7.2k views
    • 
    • SleeperZ
    • September 20, 2012

11. Stock 280ZX Turbo Dyno Graph needed

    By 24OZ, September 19, 2012
    • 2 replies
    • 944 views
    • 
    • 24OZ
    • September 20, 2012

12. ARP head stud Qs

    By brianZortiz, April 2, 2012
    • 9 replies
    • 5.1k views
    • 
    • Lazeum
    • September 19, 2012

13. Port Matching with P90 gasket on E88 Head

    By brianZortiz, September 19, 2012
    • 0 replies
    • 827 views
    • 
    • brianZortiz
    • September 19, 2012

14. l28e 240z vs. l28et 280zx! 1 2

    By xShodaimex, November 4, 2009
    • 25 replies
    • 4k views
    • 
    • HowlerMonkey
    • September 18, 2012

15. L28 Stroker Motors

    By Mike Rowe, August 28, 2012
    • 6 replies
    • 6k views
    • 
    • PMC raceengines
    • September 18, 2012

16. Head #2 at Machine Shop More Bad News

    By Ben's Z, September 16, 2012
    • 7 replies
    • 1k views
    • 
    • Sam280Z
    • September 17, 2012

17. High horsepower, nitrous L6

    By Micah, September 16, 2012
    • 3 replies
    • 1.3k views
    • 
    • johnc
    • September 17, 2012

18. Engine assembly questions - rear main cap seals and

    By inline6, February 12, 2012
    • 7 replies
    • 1.8k views
    • 
    • madkaw
    • September 15, 2012

19. Quick question on how to install rear side seals with pins.

    By Kash, September 15, 2012
    • 0 replies
    • 689 views
    • 
    • Kash
    • September 15, 2012

20. Turbo Oil Pumps

    By Ben's Z, September 13, 2012
    • 9 replies
    • 1.4k views
    • 
    • Pyro
    • September 15, 2012

21. Which Alternator on swap?

    By Ben's Z, September 14, 2012
    • 5 replies
    • 1.3k views
    • 
    • NewZed
    • September 15, 2012

22. has anyone built a 3.6L L 6 1 2

    By PMC raceengines, June 26, 2012
    • 20 replies
    • 5.3k views
    • 
    • 2 FOURTY Z!
    • September 14, 2012

23. L28E to carb or do a swap?

    By z_ya, September 14, 2012
    • 1 reply
    • 1.1k views
    • 
    • BluDestiny
    • September 14, 2012

24. Dimensions of L6 needed

    By Dead Roman, June 28, 2012
    • 6 replies
    • 1.3k views
    • 
    • HowlerMonkey
    • September 13, 2012

25. L28t club racer 1 2

    By PMC raceengines, September 3, 2012
    • 20 replies
    • 3.5k views
    • 
    • SleeperZ
    • September 12, 2012

26. The truth about N/A and Turbo Head Gaskets

    By Ben's Z, September 10, 2012
    • 1 reply
    • 1.1k views
    • 
    • Gollum
    • September 10, 2012