zentech

Asking $150 shipped. This tach came off a car with only 77k miles.

I can ship you a good oiler tube $75 + shipping. Let me know and i can expedite shipping.

I have one $50 shipped.

Then it's from an F/54 block with rods attached. You want them ?

I have a good tach for a 1978 z car in good used condition. I also have a new tach in box OEM Nissan part if you want new.

Hey Stan, just got my computer service back since last Wednesday. AT&t sucks.... no cable at the same time no internet svc. The pistons are 86 mm came out of a 280 N-42 block. I have a set of rods and may be 240's.

I have the rare E/31 cylinder head that came on the early 240's complete with camshaft. It has been sitting since rebuilt a year ago.I was planning on porting it but never got around to going that route.I have $600 into it. I also have a stage 1 camshaft for street performance or even freeway depending on 5/speed trany close or open ratio. Let me pull it out of packaging for confirmation.

I have a great gas tank and i'm in Northern California. Tank was professionally cleaned and stored over 7 years now. Let me know if you want it and i can figure a price for it. E/mail is holapsalms @yahoo.com.

I have a good 5/speed trans....

Do you have a nice cowl for an S30 car 1975. Let bme know i'm in the bay area and have a collection of engine and electrical parts.

I have several door handles if still looking.

Your location ? I have 510 friends with parts, i can check.

[Deleted - You must be a donating member to advertise on this forum]

Want to trade a pair of Weber downdraft carbs professionally jetted to match a 280Z motor. Were bought new a used for two months before doing a V-8 swap.I'm looking for an r-200 rear differential with 3:90 ratio gearing between year 1982 to 1989 in good condition. Let me know what you have and go from there. Thank you!

I sent pics again to your cell phone # 281-814-8504. Is that correct?/

Hey Ben, i sent pics of the P-90 camshaft via your cell. Let me know thanks.

I have a completely rebuilt P-90 cylinder head fresh from the machine shop, New valves, seats, seals guides etc.You said you need a good price so you must know it's pricey and the hardest one to find. Make a serious offer and don't low ball me it could be yours. PS: If you wanted a P-79, or an N-47 i have those too. Let me know.

I have a completely rebuilt P-90 cylinder head fresh from the machine shop, New valves, seats, seals guides etc.You said you need a good price so you must know it's pricey and the hardest one to find. Make a serious offer and don't low ball me it could be yours. PS: If you wanted a P-79, or an N-47 i have those too. Let me know.

If you mean the bar that the rubber grommet is on, Yes i have several of those pieces and where are you located?

That could be a hard one to find, though i may have one packed away among my stash. I'll check on it.

If you have another L-28 timing covers i'm interested in one. Let me know.

Stated in the above topic looking for a low mileage r-200 rear diff with 3:90 or 4:11 ratios. I have a few parts i'll trade such as 83ZX turbo intake/manifold less injectors and bov-valve asking $120. N-42 EFI NON EGR intake manifold less injectors $175.4 P-79 Cylinder heads. They all came off running engines and head gaskets were in perfect seating when professionally removed from blocks. One came off my F-54 a few days ago as i'm doing a P90 swap. They come with valves,lifters and springs and require minimal service before re-installing on engine block. Price for each $175.00 plus whatever shipping calculated to your zip.Call me with any questions @ 209-380-9719 or e/mail me a cell # to text pics.

I have a couple of nice quarter window finishes.I can text pics via a cell phone. thanks.