Drivetrain

6106 topics in this forum

1. Has anyone installed the Modern Motorsports 6 bolt axle end stops on the outboard?

   By cyrus, November 27, 2006
   • 9 replies
   • 1.9k views
   • 
   • mark
   • December 5, 2006

3. how much power are you putting through your r200?

   By jonus079, January 27, 2007
   • 9 replies
   • 1.9k views
   • 
   • Jelloman457
   • January 30, 2007

4. Using 280zxt cv shafts, diff, and *companion flanges* (without MM adapters)

   By Zeerari, September 16, 2008
   • 5 replies
   • 1.9k views
   • 
   • Zeerari
   • December 2, 2008

5. Vibration

   By BAlford, August 11, 2002
   • 6 replies
   • 1.9k views
   • 
   • Guest
   • August 12, 2002

6. will a rear from a 240sx work?

   By Belvedere, October 18, 2003
   • 9 replies
   • 1.9k views
   • 
   • Guest
   • October 28, 2003

7. 4.11 R180 problem

   By Heroez, July 30, 2012
   • 7 replies
   • 1.9k views
   • 
   • johnc
   • August 7, 2012

8. Where did you purchase your OBX diff?

   By subtle_driver, October 28, 2013
   • 6 replies
   • 1.9k views
   • 
   • m1ghtymaxXx
   • October 30, 2013

9. REAR DIFFERENTIAL ???

   By Guest Jim226, April 9, 2004
   • 6 replies
   • 1.9k views
   • 
   • Guest
   • April 19, 2004

10. grief.. anyone have the real skinny on r200 4:11 in a 70?

    By datjunky, May 3, 2009
    • 7 replies
    • 1.9k views
    • 
    • datjunky
    • May 5, 2009

11. 240mm clutch w/ 280zx plate is slipping...

    By Guest Loose_Screws, May 10, 2005
    • 8 replies
    • 1.9k views
    • 
    • randy 77zt
    • May 11, 2005

12. 3rd gen Mazda RX7 Differentials?!?!

    By 260DET, January 19, 2006
    • 6 replies
    • 1.9k views
    • 
    • mas28O
    • January 20, 2006

13. T5 Camaro Bell Housing Tilt

    By Miles, September 12, 2001
    • 4 replies
    • 1.9k views
    • 
    • DavyZ
    • September 14, 2001

14. 280ZXT T5 Vs. 280ZX NA 5spd.

    By Guest JAMIE T, January 13, 2003
    • 8 replies
    • 1.9k views
    • 
    • Mike C
    • January 14, 2003

15. I need bolts

    By Toysport, June 29, 2005
    • 10 replies
    • 1.9k views
    • 
    • Toysport
    • July 1, 2005

16. Nissan Half-shaft U-joints

    By fp280z, June 12, 2006
    • 1 reply
    • 1.9k views
    • 
    • Z24O
    • June 15, 2006

17. Painting Diff. - Heat issues?

    By attworth, March 30, 2009
    • 9 replies
    • 1.9k views
    • 
    • RocknTommy
    • April 7, 2009

18. Need pinion angles...

    By dizzle, July 20, 2010
    • 4 replies
    • 1.9k views
    • 
    • madkaw
    • September 26, 2013

19. R200 stub axels question

    By Dale280z, February 28, 2023
    • 6 replies
    • 1.9k views
    • 
    • Dale280z
    • February 28, 2023

20. 280zx drivetrain upgrades?

    By PhaTTy, June 9, 2005
    • 13 replies
    • 1.9k views
    • 
    • PhaTTy
    • June 13, 2005

21. VLSD info

    By 240Z-DET, October 8, 2005
    • 8 replies
    • 1.9k views
    • 
    • evildky
    • October 11, 2005

22. T-5 bellhousing measurement,(height) needed.

    By Bob_H, September 13, 2010
    • 4 replies
    • 1.9k views
    • 
    • Bob_H
    • September 16, 2010

23. 300zxt halfshaft outer flange?

    By Jersey, October 19, 2005
    • 8 replies
    • 1.9k views
    • 
    • Jersey
    • October 25, 2005

24. Slave cylinder...

    By Guest ON3GO, December 21, 2005
    • 9 replies
    • 1.9k views
    • 
    • Guest
    • January 18, 2006

25. Found 300zxt r200clsd,now what?

    By crazy canuck Z8, October 6, 2006
    • 10 replies
    • 1.9k views
    • 
    • JMortensen
    • October 6, 2006

26. viscous or clutch R200 ???

    By shupee, July 2, 2013
    • 7 replies
    • 1.9k views
    • 
    • JMortensen
    • July 3, 2013