Nissan L6 Forum

6897 topics in this forum

1. So what does an LD-powered Maxima go for in good running condition?

   By Daeron, January 28, 2009
   • 8 replies
   • 1k views
   • 
   • HowlerMonkey
   • January 31, 2009

3. L24 valve job questions- new lash pads/options?

   By Mn_Z_Man, May 7, 2009
   • 1 reply
   • 1k views
   • 
   • WizardBlack
   • May 7, 2009

4. Where can I get oil line plug front & rear short block?

   By tamo3, October 30, 2012
   • 5 replies
   • 1k views
   • 
   • rayaapp2
   • November 2, 2012

5. Various pallnet questions

   By turbogrill, August 11, 2017
   • 2 replies
   • 1k views
   • 
   • madkaw
   • August 11, 2017

6. best intake mannie for n/a

   By Eric, October 3, 2005
   • 3 replies
   • 1k views
   • 
   • 1 fast z
   • October 4, 2005

7. Forged pistons for L28ET

   By Wide260z, March 19, 2006
   • 1 reply
   • 1k views
   • 
   • 510six
   • March 19, 2006

8. new engine souunds good!

   By echocluster@hotmail.com, July 4, 2005
   • 1 reply
   • 1k views
   • 
   • Guest
   • July 8, 2005

9. Bottom alternator bolts keep coming out!!

   By SU'dCrazy280, September 6, 2006
   • 3 replies
   • 1k views
   • 
   • WHP
   • September 7, 2006

10. New found problems on parked L28et swap

    By grey280, January 14, 2009
    • 3 replies
    • 1k views
    • 
    • grey280
    • January 14, 2009

11. When Aluminum Melts.....

    By jc052685, August 19, 2009
    • 4 replies
    • 1k views
    • 
    • MAG58
    • August 19, 2009

12. l28et surging and dying at startup

    By m1ghtymaxXx, August 22, 2007
    • 2 replies
    • 1k views
    • 
    • schwiplarkin
    • August 23, 2007

13. timing degree and rpm for a tuned 390 cfm holley install

    By madmax37, November 22, 2010
    • 0 replies
    • 1k views
    • 
    • madmax37
    • November 22, 2010

14. Timing Chain Guide, Slack Side Quality

    By dapiper, May 24, 2005
    • 2 replies
    • 1k views
    • 
    • EZ-E
    • May 24, 2005

15. Weird idle rpm change from cold to hot

    By george.bryant, April 10, 2006
    • 4 replies
    • 1k views
    • 
    • nienberg.11
    • April 11, 2006

16. checking installed heights and valve seals to use...

    By inline6, May 18, 2010
    • 1 reply
    • 1k views
    • 
    • inline6
    • May 24, 2010

17. Lash pad compatibility question

    By aarang, January 15, 2007
    • 4 replies
    • 1k views
    • 
    • aarang
    • January 17, 2007

18. Aluminum pan vs. ARP main studs

    By evildky, March 27, 2009
    • 3 replies
    • 1k views
    • 
    • evildky
    • March 30, 2009

19. P90A solid lifter

    By Zellthetunerr, July 10, 2022
    • 0 replies
    • 1k views
    • 
    • Zellthetunerr
    • July 10, 2022

20. Do anyone know this car

    By SUNMASTER, January 1, 2007
    • 0 replies
    • 1k views
    • 
    • SUNMASTER
    • January 1, 2007

21. vent hose for fuel cel

    By slowride, August 1, 2011
    • 1 reply
    • 1k views
    • 
    • beermanpete
    • August 2, 2011

22. which fuel filter? (urgent!)

    By mnelson260z, August 17, 2005
    • 1 reply
    • 1k views
    • 
    • Guest
    • August 17, 2005

23. powder coated carbs

    By 4everDATSUN, February 16, 2006
    • 2 replies
    • 1k views
    • 
    • Cruez
    • February 17, 2006

24. need help on 3.1 build.

    By voodoo240z, November 19, 2007
    • 1 reply
    • 1k views
    • 
    • JMortensen
    • November 19, 2007

25. switching to a 2mm mhg

    By datz280, January 31, 2008
    • 3 replies
    • 1k views
    • 
    • savageskaterkid
    • February 1, 2008

26. To Extrude hone a P90? Opinions?

    By rags, August 30, 2008
    • 3 replies
    • 1k views
    • 
    • rags
    • September 1, 2008