Fabrication / Welding

1332 topics in this forum

1. Welding Roll Bar to Roof

   By D1t, August 20, 2022
   • 9 replies
   • 4.3k views
   • 
   • jhm
   • September 8, 2022

3. Anyone fabricated a new front crossmember?

   By desert dog, February 18, 2006
   • 8 replies
   • 2.9k views
   • 
   • fastzcars
   • February 21, 2006

4. Thank you Gray Davis [not political] it's actually about a welder...

   By Lunar240z, March 22, 2006
   • 8 replies
   • 2.2k views
   • 
   • Lunar240z
   • May 19, 2006

5. About to get a Miller EconoTIG, help with 230v source...

   By BLOZ UP, April 2, 2006
   • 8 replies
   • 4.8k views
   • 
   • grumpyvette
   • April 5, 2006

6. Nibblers and or shears

   By Wheeler, May 9, 2006
   • 8 replies
   • 3.7k views
   • 
   • 2126
   • May 10, 2006

7. What metal to get to practice MIG?

   By Guest TegRacer324, May 21, 2006
   • 8 replies
   • 1.8k views
   • 
   • JMortensen
   • May 26, 2006

8. Preventing tubing from rusting from the inside out?

   By Guest TegRacer324, July 26, 2006
   • 8 replies
   • 12.4k views
   • 
   • Guest
   • July 30, 2006

9. 240 t-top?

   By zedsaid, December 20, 2006
   • 8 replies
   • 2.9k views
   • 
   • Paz8
   • December 26, 2006

10. B&M shifter trans tunnel cut out question

    By gretchen/jason, April 8, 2007
    • 8 replies
    • 4.1k views
    • 
    • getZ
    • July 13, 2007

11. Rear wheel well question

    By gretchen/jason, May 27, 2007
    • 8 replies
    • 2.1k views
    • 
    • JMortensen
    • May 28, 2007

12. Need advice on metal to make a harness bar...

    By cpt jack, June 27, 2007
    • 8 replies
    • 2.1k views
    • 
    • JMortensen
    • June 27, 2007

13. 8$ + Hours of Drilling and Grinding = 240sx Throttlebody Spacer

    By Yorgee, July 5, 2007
    • 8 replies
    • 1.9k views
    • 
    • Yorgee
    • July 5, 2007

14. harbor freight welders

    By zmaster, August 4, 2007
    • 8 replies
    • 3k views
    • 
    • grumpyvette
    • August 5, 2007

15. Need flange welded to cast manifold, anyone know of a good welder in southern WI?

    By Evan Purple240zt, October 30, 2007
    • 8 replies
    • 1.6k views
    • 
    • Evan Purple240zt
    • November 12, 2007

16. Brazing a rust hole

    By Dane, October 31, 2007
    • 8 replies
    • 15.4k views
    • 
    • bobbyc
    • November 1, 2007

17. Isuzu Intercooler

    By MaTTSuN, April 18, 2008
    • 8 replies
    • 2.7k views
    • 
    • MaTTSuN
    • May 8, 2008

18. Floor pans any ideas?

    By tightywhitey185, November 9, 2008
    • 8 replies
    • 2.4k views
    • 
    • joker120
    • November 12, 2008

19. Fabrication Help

    By Nismo280zEd, November 11, 2008
    • 8 replies
    • 2.3k views
    • 
    • joker120
    • November 12, 2008

20. Argon tanks

    By tightywhitey185, December 3, 2008
    • 8 replies
    • 2.1k views
    • 
    • ben280zx
    • December 4, 2008

21. Fender flare removal suggestions?????

    By Gixxer Squid, December 20, 2008
    • 8 replies
    • 2.4k views
    • 
    • Gixxer Squid
    • December 22, 2008

22. Best clamps for drill press?

    By Evan Purple240zt, February 2, 2009
    • 8 replies
    • 2.6k views
    • 
    • (goldfish)
    • February 22, 2009

23. First attempt at building motor mounts. Input is appriciated!

    By i r teh noobz, May 22, 2009
    • 8 replies
    • 2.5k views
    • 
    • Magnum380Z
    • May 25, 2009

24. Quick n' Easy ZXT "Cold Air Intake"

    By Challenger, June 4, 2009
    • 8 replies
    • 3.7k views
    • 
    • srbigbutt
    • June 5, 2009

25. rust repair on a series 1 240z

    By 240z!!!, June 25, 2009
    • 8 replies
    • 4.9k views
    • 
    • johnc
    • July 13, 2009

26. Need some suggestions with roll bar

    By jkgts1, August 26, 2009
    • 8 replies
    • 1.9k views
    • 
    • jkgts1
    • August 27, 2009