Drivetrain

6106 topics in this forum

1. Silvermine Motorsports -Ford 8.8 Rear End Conversion for 240z

   By toolman, October 4, 2023
   • 7 replies
   • 5.3k views
   • 
   • toolman
   • February 11, 2025

3. New Pilot Bearing, Clutch, Pressure Plate, and Throw Out Bearing 1 2

   By jacob80, April 6, 2010
   • 29 replies
   • 5.3k views
   • 
   • woldson
   • April 10, 2010

4. Reinforcing the front subframe

   By zTrollop, April 28, 2020
   • 19 replies
   • 5.3k views
   • 
   • 74_5.0L_Z
   • May 29, 2020

5. Welding on CV shafts

   By Z-TARD, April 16, 2004
   • 11 replies
   • 5.3k views
   • 
   • rytherwr
   • April 28, 2004

6. Q45 Diff Swap, Axle Problem

   By LS1 Z, May 19, 2007
   • 18 replies
   • 5.3k views
   • 
   • Datsun570z
   • April 15, 2014

7. 9 Inch Ford rear end conversion

   By Two40MuscleZ, October 27, 2001
   • 13 replies
   • 5.2k views
   • 
   • stony
   • August 30, 2002

8. 280ZX AWD Conversion?

   By Guest TwinCam, April 17, 2008
   • 13 replies
   • 5.2k views
   • 
   • DrEaM
   • April 21, 2008

9. Tremec TKO Transmission

   By hjc74260Z, September 9, 2003
   • 7 replies
   • 5.2k views
   • 
   • hjc74260Z
   • September 13, 2003

10. Lightweight Flywheel for 1982 Turbo Z 1 2

    By jtmny1999, September 12, 2004
    • 22 replies
    • 5.2k views
    • 
    • jtmny1999
    • September 20, 2004

11. Snapped a R200 "mustache" bar ! How Common? Cure? 1 2

    By Guest Anonymous, June 5, 2002
    • 20 replies
    • 5.2k views
    • 
    • The Infidel
    • May 19, 2009

12. Potential Group Buy: BOLT-ON CV ADAPTORS, proven design 1 2

    By Modern Motorsports Ltd, July 25, 2001
    • 37 replies
    • 5.2k views
    • 
    • icewtr
    • February 20, 2007

13. 300zx Z31 Turbo CV Shaft Disassembly

    By Ezzie, February 1, 2005
    • 10 replies
    • 5.2k views
    • 
    • Ezzie
    • February 2, 2005

14. Early 6-bolt side flange for R200 available?

    By ezzzzzzz, November 22, 2006
    • 10 replies
    • 5.2k views
    • 
    • 510six
    • November 24, 2006

15. performance wheel bearings?

    By AZGhost623, May 26, 2015
    • 11 replies
    • 5.2k views
    • 
    • JMortensen
    • July 20, 2015

16. What's the highest gear ratio for R200 or other strong rear?

    By Guest Magnum Rockwilder, October 29, 2004
    • 10 replies
    • 5.2k views
    • 
    • Guest
    • October 30, 2004

17. Differential Identification... R200

    By Lost Soul, January 19, 2012
    • 6 replies
    • 5.2k views
    • 
    • Lost Soul
    • January 19, 2012

18. 280zx vibration under heavy load

    By bigbreak_2000, February 28, 2014
    • 10 replies
    • 5.2k views
    • 
    • Savage42
    • June 27, 2014

19. Deep into yet another rear end clunk 1 2

    By wheelerz31, June 18, 2015
    • 23 replies
    • 5.1k views
    • 
    • JMortensen
    • June 24, 2015

20. r200 lsd broke in half

    By bryan01, July 8, 2013
    • 19 replies
    • 5.1k views
    • 
    • johnc
    • July 9, 2013

21. So much for the indestructable R200 1 2

    By zthis, July 1, 2007
    • 26 replies
    • 5.1k views
    • 
    • OlderThanMe
    • July 7, 2007

22. Datsun 5-speed 5th to reverse lockout?

    By cygnusx1, March 27, 2012
    • 11 replies
    • 5.1k views
    • 
    • cygnusx1
    • April 2, 2012

23. R200 questions please help

    By Guest Busarail, March 2, 2006
    • 12 replies
    • 5.1k views
    • 
    • OlderThanMe
    • March 15, 2006

24. Silvermine R180 Stub Axles?

    By JeffB240z, November 28, 2017   

    • r180
    • stub axles
    • 7 replies
    • 5.1k views
    • 
    • jhm
    • April 10, 2022

25. How to tell if R200 is LSD

    By socorob, April 13, 2013
    • 5 replies
    • 5.1k views
    • 
    • johnc
    • April 15, 2013

26. Where to source counter shaft bearing for the 83 280ZX FS5W71B

    By wigenOut-S30, September 11, 2014
    • 12 replies
    • 5.1k views
    • 
    • NewZed
    • May 2, 2016