Fabrication / Welding

1331 topics in this forum

1. Fiberglass Doors

   By 260DET, June 29, 2012
   • 4 replies
   • 1.9k views
   • 
   • suparman
   • June 30, 2012

3. New fab shop in So-Cal!

   By Guest koji187, January 17, 2008
   • 3 replies
   • 1.9k views
   • 
   • 2126
   • January 31, 2008

4. Thank you Gray Davis [not political] it's actually about a welder...

   By Lunar240z, March 22, 2006
   • 8 replies
   • 1.8k views
   • 
   • Lunar240z
   • May 19, 2006

5. Need advice on floor repair

   By skirkland1980, June 22, 2015
   • 4 replies
   • 1.8k views
   • 
   • skirkland1980
   • June 25, 2015

6. fiberglass mold making

   By rdsk8ter, January 8, 2007
   • 6 replies
   • 1.8k views
   • 
   • Careless
   • January 9, 2007

7. New Welder

   By cheftrd, May 1, 2008
   • 6 replies
   • 1.8k views
   • 
   • cheftrd
   • May 2, 2008

8. S30 280zx disk conversion brackets?

   By ModernS30, April 30, 2010
   • 7 replies
   • 1.8k views
   • 
   • tyler031734
   • May 3, 2010

9. welding stainless to other metal

   By madmanadam, June 5, 2006
   • 5 replies
   • 1.8k views
   • 
   • Rumnhammer
   • June 21, 2006

10. Header designs: N/A and Turbo

    By OlderThanMe, August 29, 2006
    • 7 replies
    • 1.8k views
    • 
    • johnc
    • September 11, 2006

11. Tilt front-end

    By gjc5500, February 21, 2007
    • 4 replies
    • 1.8k views
    • 
    • gjc5500
    • February 21, 2007

12. porosity

    By Lunar240z, June 8, 2006
    • 7 replies
    • 1.8k views
    • 
    • johnc
    • June 8, 2006

13. Do oil and copper mix?

    By grannyknot, June 28, 2015
    • 3 replies
    • 1.8k views
    • 
    • 88dangerdan
    • June 29, 2015

14. Hot or cold rolled square tube for frame rails??

    By blake culp, February 23, 2009
    • 3 replies
    • 1.8k views
    • 
    • Flexicoker
    • February 24, 2009

15. Need some info from metal working gurus..

    By Cruez, February 1, 2007
    • 16 replies
    • 1.8k views
    • 
    • 2003z
    • February 4, 2007

16. Welder Reel Tensioner

    By Careless, May 28, 2007
    • 6 replies
    • 1.8k views
    • 
    • Careless
    • June 3, 2007

17. Helmet/lens suggestions

    By HowlerMonkey, March 29, 2009
    • 5 replies
    • 1.8k views
    • 
    • tonycharger72
    • March 30, 2009

18. 76 280z floor pans

    By HOLLAATYABOYY1, May 24, 2018
    • 1 reply
    • 1.8k views
    • 
    • Ryanotown22
    • June 3, 2018

19. The Welder Lives!

    By Some-Guy, April 28, 2006
    • 6 replies
    • 1.8k views
    • 
    • Some-Guy
    • April 30, 2006

20. Interior roll cages - jd2 model 32 bender

    By JensenBro1, October 16, 2016
    • 0 replies
    • 1.8k views
    • 
    • JensenBro1
    • October 16, 2016

21. Roll cage: has anyone been able to make a knee-bar that doesn't interfere with radio and heater controls?

    By RebekahsZ, December 28, 2013
    • 4 replies
    • 1.8k views
    • 
    • RebekahsZ
    • December 30, 2013

22. Experience with MSA Floors and Frame rails?

    By T-Bone028, February 24, 2008
    • 2 replies
    • 1.8k views
    • 
    • Sparks280zt
    • February 25, 2008

23. Cheap Velocity Stacks

    By blaze73, March 5, 2008
    • 1 reply
    • 1.8k views
    • 
    • SATAN
    • March 11, 2008

24. What does the Hybridz Community think of this compressor?

    By wonderllama, January 16, 2007
    • 9 replies
    • 1.8k views
    • 
    • 71stroker
    • January 17, 2007

25. Trans adaptor l28 to chevy trans?

    By twoeightythreez, January 26, 2014
    • 2 replies
    • 1.8k views
    • 
    • xero_xero
    • February 3, 2014

26. Rear wheel well question

    By gretchen/jason, May 27, 2007
    • 8 replies
    • 1.8k views
    • 
    • JMortensen
    • May 28, 2007