Fabrication / Welding

1331 topics in this forum

1. now you may question my sanity after this........

   By Some-Guy, April 30, 2006
   • 18 replies
   • 2.4k views
   • 
   • Some-Guy
   • May 4, 2006

3. In house electrical Wiring for a welder Q

   By yo2001, September 7, 2008
   • 13 replies
   • 2.4k views
   • 
   • rdsk8ter
   • September 16, 2008

4. Xe7 projector headlights

   By stroked_Z, February 3, 2009
   • 7 replies
   • 2.4k views
   • 
   • jerryb
   • February 3, 2009

5. First post, been doing some research about floor pan replacements

   By The love of JDM, November 27, 2008
   • 9 replies
   • 2.4k views
   • 
   • The love of JDM
   • January 3, 2009

6. Building a welder TODAY

   By Some-Guy, April 23, 2006
   • 12 replies
   • 2.4k views
   • 
   • Some-Guy
   • April 30, 2006

7. Looking for an Electric Die Grinder Comparable to my Pneumatic

   By cockerstar, June 27, 2013
   • 13 replies
   • 2.4k views
   • 
   • yellowoctupus
   • July 2, 2013

8. Any Sheetmetal Fabricators Out There?

   By Scottie-GNZ, July 14, 2007
   • 13 replies
   • 2.4k views
   • 
   • Scottie-GNZ
   • July 18, 2007

9. Vacuum Distribution Block

   By dts300z, April 2, 2010
   • 8 replies
   • 2.4k views
   • 
   • dts300z
   • April 9, 2010

10. Need Front Air Dam Support Brackets? I sure did.

    By Yorgee, May 30, 2007
    • 11 replies
    • 2.4k views
    • 
    • proxlamus©
    • May 30, 2007

11. I Need Welding Tips

    By miamiKnights, December 21, 2006
    • 15 replies
    • 2.4k views
    • 
    • datsunlover
    • December 25, 2006

12. Hidden wipers

    By Six_Shooter, February 21, 2008
    • 9 replies
    • 2.4k views
    • 
    • Six_Shooter
    • February 22, 2008

13. any parts needed to be fabbed?

    By inlawZ, December 18, 2008
    • 11 replies
    • 2.4k views
    • 
    • inlawZ
    • February 13, 2009

14. Roll bar main hoop conflicts with quarter glass screws

    By RebekahsZ, February 23, 2014
    • 9 replies
    • 2.4k views
    • 
    • RebekahsZ
    • May 27, 2014

15. how many of you use or own plazma cutters

    By grumpyvette, July 27, 2007
    • 15 replies
    • 2.4k views
    • 
    • Mike C
    • August 9, 2007

16. Curves/bends in sheet?

    By Shift, April 16, 2008
    • 10 replies
    • 2.4k views
    • 
    • perana
    • April 17, 2008

17. 240z rear end repair

    By Neverdone, March 1, 2017
    • 5 replies
    • 2.4k views
    • 
    • tim.d
    • March 3, 2017

18. Floor board welding help

    By gretchen/jason, May 6, 2007
    • 6 replies
    • 2.4k views
    • 
    • gretchen/jason
    • May 26, 2007

19. Sand blasting and Silicosis. What you should know

    By SATAN, March 22, 2008
    • 14 replies
    • 2.4k views
    • 
    • Careless
    • March 23, 2008

20. Looking for MIG

    By doublez, February 19, 2010
    • 11 replies
    • 2.4k views
    • 
    • doublez
    • March 10, 2010

21. ITB design

    By savageskaterkid, December 11, 2009
    • 3 replies
    • 2.3k views
    • 
    • savageskaterkid
    • December 11, 2009

22. Welding Help

    By Nismo280zEd, December 20, 2008
    • 12 replies
    • 2.3k views
    • 
    • Nismo280zEd
    • December 30, 2008

23. Best clamps for drill press?

    By Evan Purple240zt, February 2, 2009
    • 8 replies
    • 2.3k views
    • 
    • (goldfish)
    • February 22, 2009

24. Fabbing Mounts For An Aluminum Dash

    By Zzeal, June 23, 2013
    • 5 replies
    • 2.3k views
    • 
    • Zzeal
    • June 25, 2013

25. CENTER EXIT EXHAUST SETUP

    By DEVIL-Z 1973, April 24, 2010
    • 4 replies
    • 2.3k views
    • 
    • DEVIL-Z 1973
    • April 24, 2010

26. Pipe seam split! Whats the best repair???

    By BURLEIGH, November 16, 2009
    • 6 replies
    • 2.3k views
    • 
    • BURLEIGH
    • November 17, 2009