Fabrication / Welding

1331 topics in this forum

1. Auto Darkening Helment for $100?

   By NCchris, December 16, 2014
   • 8 replies
   • 2k views
   • 
   • thezguy
   • December 17, 2014

3. tig/plasma combo machine

   By stony, November 6, 2007
   • 5 replies
   • 2k views
   • 
   • proxlamus©
   • November 8, 2007

4. When Good Pot Metal Goes Bad

   By Zinpieces, October 10, 2011
   • 0 replies
   • 2k views
   • 
   • Zinpieces
   • October 10, 2011

5. 280z fuel tank repair Question

   By Graphitez, December 29, 2010
   • 2 replies
   • 2k views
   • 
   • Graphitez
   • December 30, 2010

6. welding stainless to other metal

   By madmanadam, June 5, 2006
   • 5 replies
   • 2k views
   • 
   • Rumnhammer
   • June 21, 2006

7. 280z hub axles conversion

   By Logoleaf, August 11, 2015
   • 4 replies
   • 2k views
   • 
   • whatnow123
   • August 12, 2015

8. What does the Hybridz Community think of this compressor?

   By wonderllama, January 16, 2007
   • 9 replies
   • 2k views
   • 
   • 71stroker
   • January 17, 2007

9. Plate and tube thickness guidance

   By 280Z-LS3, October 29, 2020
   • 4 replies
   • 2k views
   • 
   • JMortensen
   • October 30, 2020

10. How much are you paying for Gas and cylinders

    By Beck, July 14, 2009
    • 4 replies
    • 2k views
    • 
    • tannji
    • July 17, 2009

11. Zedd engine frame rails issue...?

    By FairladyGTR, February 2, 2020
    • 6 replies
    • 2k views
    • 
    • Chickenwing
    • March 17, 2020

12. Cast Iron test?

    By Techtron, February 6, 2007
    • 6 replies
    • 2k views
    • 
    • AK-Z
    • February 9, 2007

13. 260 swap engine mounts

    By s30red240z, January 31, 2010
    • 4 replies
    • 2k views
    • 
    • hoov100
    • February 6, 2010

14. Best way to remove trim brackets?

    By burninator, January 27, 2010
    • 5 replies
    • 2k views
    • 
    • burninator
    • April 19, 2010

15. The Welder Lives!

    By Some-Guy, April 28, 2006
    • 6 replies
    • 2k views
    • 
    • Some-Guy
    • April 30, 2006

16. Recommendation for bead roller

    By GeeZ, October 13, 2009
    • 5 replies
    • 2k views
    • 
    • mrandrei
    • October 27, 2009

17. Roll cage: has anyone been able to make a knee-bar that doesn't interfere with radio and heater controls?

    By RebekahsZ, December 28, 2013
    • 4 replies
    • 2k views
    • 
    • RebekahsZ
    • December 30, 2013

18. S30 Roll Bar Dimensions

    By TieFighter88, September 24, 2014
    • 3 replies
    • 2k views
    • 
    • heavy85
    • September 26, 2014

19. Hot or cold rolled square tube for frame rails??

    By blake culp, February 23, 2009
    • 3 replies
    • 2k views
    • 
    • Flexicoker
    • February 24, 2009

20. Flanges for SCH10 pipe?

    By BLOZ UP, March 21, 2011
    • 3 replies
    • 2k views
    • 
    • BLOZ UP
    • March 23, 2011

21. What was done to this L28 head?!?

    By Yorgee, June 10, 2007
    • 4 replies
    • 2k views
    • 
    • BRAAP
    • June 10, 2007

22. Trans adaptor l28 to chevy trans?

    By twoeightythreez, January 26, 2014
    • 2 replies
    • 2k views
    • 
    • xero_xero
    • February 3, 2014

23. warpage prevention

    By skirkland1980, December 29, 2015
    • 2 replies
    • 2k views
    • 
    • skirkland1980
    • December 31, 2015

24. 73 240z front air duct rot

    By Builds and Brews, August 23, 2019   

    • 240z
    • rust
    • (and 1 more)

      Tagged with:

      • 240z
      • rust
      • repair
    • 2 replies
    • 2k views
    • 
    • rturbo 930
    • August 29, 2019

25. reusing floor pans from another z

    By datsundave, April 23, 2010
    • 5 replies
    • 2k views
    • 
    • sticky280zx
    • May 9, 2010

26. Experience with MSA Floors and Frame rails?

    By T-Bone028, February 24, 2008
    • 2 replies
    • 2k views
    • 
    • Sparks280zt
    • February 25, 2008