Fabrication / Welding

1333 topics in this forum

1. welding/welder question

   By 73_240z, October 31, 2006
   • 18 replies
   • 3.6k views
   • 
   • kuntry
   • November 1, 2006

3. Welds Cracking on rust patches

   By at-jefft, May 11, 2010
   • 15 replies
   • 5.8k views
   • 
   • Nismo280zEd
   • May 26, 2010

4. well its not fabing but ive seen a lot of dash talk in here

   By atx_s130, February 13, 2007
   • 2 replies
   • 1.5k views
   • 
   • atx_s130
   • February 15, 2007

5. Well, I did, bought a welder finally

   By panachedk, March 17, 2008
   • 15 replies
   • 2.5k views
   • 
   • panachedk
   • March 20, 2008

6. Welp.. Im building a Rotisserie from Engine Stands.. **Pics** 1 2 3

   By proxlamus©, August 19, 2009
   • 59 replies
   • 78.4k views
   • 
   • 250z
   • February 20, 2011

7. what about this rear diffuser idea 1 2

   By J__, September 13, 2007
   • 28 replies
   • 10.9k views
   • 
   • marcg
   • September 27, 2007

8. What does the Hybridz Community think of this compressor?

   By wonderllama, January 16, 2007
   • 9 replies
   • 2.1k views
   • 
   • 71stroker
   • January 17, 2007

9. what gauge metal!!

   By unbreakable, March 11, 2009
   • 3 replies
   • 1.7k views
   • 
   • zclubhouse
   • March 12, 2009

10. What metal to get to practice MIG?

    By Guest TegRacer324, May 21, 2006
    • 8 replies
    • 1.9k views
    • 
    • JMortensen
    • May 26, 2006

11. What should I try to save?

    By kph, August 3, 2012
    • 1 reply
    • 1.4k views
    • 
    • johnc
    • August 3, 2012

12. What TIG to buy? 1 2 3

    By dr_hunt, September 7, 2006
    • 46 replies
    • 13.9k views
    • 
    • dr_hunt
    • September 22, 2006

13. What Tool To Use To Cut Aluminum Intercooler Piping? 1 2

    By slownrusty, November 24, 2007
    • 22 replies
    • 18.6k views
    • 
    • mcmike280z
    • December 1, 2007

14. What tubing bender do you use? 1 2

    By MoNkEyT88, March 21, 2012
    • 32 replies
    • 26k views
    • 
    • RebekahsZ
    • December 18, 2012

15. What type of pipe for intercooler

    By stony, October 20, 2007
    • 13 replies
    • 3.1k views
    • 
    • stony
    • November 3, 2007

16. What was done to this L28 head?!?

    By Yorgee, June 10, 2007
    • 4 replies
    • 2k views
    • 
    • BRAAP
    • June 10, 2007

17. What's the cost of a fuel cell install?

    By ruggedbert, April 11, 2009
    • 7 replies
    • 4.7k views
    • 
    • 240zdan
    • July 5, 2009

18. When Good Pot Metal Goes Bad

    By Zinpieces, October 10, 2011
    • 0 replies
    • 2.1k views
    • 
    • Zinpieces
    • October 10, 2011

19. Where are Spots to Weld - Restoration with V8

    By xelocity, April 1, 2013   

    • restoration
    • v8
    • (and 2 more)

      Tagged with:

      • restoration
      • v8
      • welding
      • fabrication
    • 2 replies
    • 2.8k views
    • 
    • xelocity
    • April 1, 2013

20. where does the water leak from?

    By greghassen, February 6, 2011
    • 4 replies
    • 2k views
    • 
    • 19762802+2
    • February 6, 2011

21. Where to buy door skins?

    By jeg60driver, March 1, 2013
    • 1 reply
    • 1.4k views
    • 
    • morbias
    • March 1, 2013

22. Where to Order Stainless Tubing and Vbands

    By Dat73z, June 14, 2021
    • 10 replies
    • 4.5k views
    • 
    • LooseRocks
    • July 1, 2021

23. Where to start?!

    By sKwared, February 7, 2012
    • 9 replies
    • 3k views
    • 
    • seattlejester
    • February 8, 2012

24. Which Air Compressor to get? *xmas gift to me* 1 2

    By Guest 280ZForce, December 7, 2006
    • 22 replies
    • 4.2k views
    • 
    • DemonZ
    • December 9, 2006

25. Which welder?

    By Guest, January 1, 1970
    • 0 replies
    • 1.3k views
    • 
    • Guest
    • January 1, 1970

26. Who daily drives their Z without heater/a.c.

    By goldenchild7801, June 5, 2006
    • 15 replies
    • 2.9k views
    • 
    • goldenchild7801
    • June 6, 2006