Nissan L6 Forum

6890 topics in this forum

1. Zxt richy rich

   By calvin280zxt, May 6, 2016
   • 4 replies
   • 1.3k views
   • 
   • wolfalp1592
   • May 31, 2016

3. 4 barrel set up higher than 390cfm

   By Datsun#1, June 25, 2015
   • 3 replies
   • 3.6k views
   • 
   • McGruber21
   • May 30, 2016

4. New rocker arms?

   By Jss240z, May 19, 2016   

   • Rockers p79
   • 12 replies
   • 1.7k views
   • 
   • Leon
   • May 25, 2016

5. Crank damper loose on snout

   By Gearheadmatt, May 23, 2016
   • 1 reply
   • 985 views
   • 
   • TimZ
   • May 24, 2016

6. Two open valves on tdc

   By Austing, May 19, 2016
   • 4 replies
   • 982 views
   • 
   • Leon
   • May 19, 2016

7. knife edge crank 1 2 3

   By ablesnead, April 20, 2013
   • 46 replies
   • 15.2k views
   • 
   • zredbaron
   • May 18, 2016

8. O ring cylinder head 1 2

   By DAT240Z, April 17, 2016
   • 24 replies
   • 8.6k views
   • 
   • Tony D
   • May 17, 2016

9. Goerz Paeco DOHC Head

   By HybridHydra, May 11, 2016
   • 2 replies
   • 1.9k views
   • 
   • Tony D
   • May 17, 2016

10. 240sx throttle body on l28

    By FlameShadow, February 8, 2016
    • 6 replies
    • 2.4k views
    • 
    • Austing
    • May 15, 2016

11. L28 DEATH rattle!

    By pnoland, April 30, 2016
    • 16 replies
    • 2.2k views
    • 
    • pnoland
    • May 11, 2016

12. Custom Manifold for 6 Carburetor Setup 1 2 3

    By pkz, August 25, 2015   

    • l28
    • manifold
    • (and 1 more)

      Tagged with:

      • l28
      • manifold
      • carburetor
    • 48 replies
    • 17k views
    • 
    • pkz
    • May 11, 2016

13. ARP head studs won't go in all the way. What do I do?

    By dpuma8, May 8, 2016
    • 4 replies
    • 3.6k views
    • 
    • dpuma8
    • May 10, 2016

14. N/A Dished piston F54?

    By Flatout_friesen, May 7, 2016   

    • dished
    • turbo
    • (and 1 more)

      Tagged with:

      • dished
      • turbo
      • project l6 l28
    • 3 replies
    • 2k views
    • 
    • malibud
    • May 10, 2016

15. E88 head question?

    By S30Stig, March 21, 2016
    • 8 replies
    • 2.7k views
    • 
    • S30Stig
    • May 7, 2016

16. Small chip on piston. Does this need to be replaced?

    By dpuma8, May 2, 2016
    • 6 replies
    • 4k views
    • 
    • LLave
    • May 4, 2016

17. Offsetting cylinder head

    By mutantZ, May 2, 2016
    • 3 replies
    • 1.5k views
    • 
    • Xnke
    • May 3, 2016

18. Manual trans output case repair?

    By redfogo, April 16, 2016
    • 11 replies
    • 1.6k views
    • 
    • Tony D
    • May 1, 2016

19. Kaminari Headgasket

    By HuD 91gt, April 26, 2016
    • 3 replies
    • 1.2k views
    • 
    • SHADY280
    • April 30, 2016

20. E88 head vs p90a head

    By az240z, April 17, 2016
    • 6 replies
    • 3k views
    • 
    • supernova_6969
    • April 30, 2016

21. Dry fouling on cyl 5 and 6 plugs; going nuts. Help?

    By supernova_6969, April 26, 2016   

    • dry fouling
    • 12 replies
    • 1.8k views
    • 
    • supernova_6969
    • April 30, 2016

22. Rebuilt l28 only runs with fuel pump unplugged

    By jhill, April 21, 2016
    • 6 replies
    • 1.3k views
    • 
    • jhill
    • April 28, 2016

23. F54 flat piston w/ N42, what cam?

    By 6inline, April 27, 2016
    • 5 replies
    • 1.7k views
    • 
    • Xnke
    • April 28, 2016

24. 280zx Won't Start - Low Fuel Pump Voltage

    By mazikowski, April 11, 2016
    • 4 replies
    • 2.2k views
    • 
    • supernova_6969
    • April 27, 2016

25. Would you use an asbestos intake/exhaust gasket?

    By jeffer949, April 4, 2016
    • 9 replies
    • 3.4k views
    • 
    • 510six
    • April 22, 2016

26. PCV/Crank Case Evac 1 2

    By luseboy, March 30, 2016
    • 25 replies
    • 6.7k views
    • 
    • luseboy
    • April 19, 2016