Nissan L6 Forum

6901 topics in this forum

1. Is this cam going to screw up a turbo L28 motor?

   By Badler, October 30, 2014   

   • cam
   • turbo
   • (and 1 more)

     Tagged with:

     • cam
     • turbo
     • l28
   • 7 replies
   • 2.6k views
   • 
   • Tony D
   • November 2, 2014

3. How much power can the L24 Rods handle?

   By kimdrummel, October 28, 2014   

   • turbo
   • L28
   • (and 1 more)

     Tagged with:

     • turbo
     • L28
     • L24
   • 15 replies
   • 5.2k views
   • 
   • Tony D
   • November 3, 2014

4. 1971 240z restoration/build 1 2 3 4

   By Brendanm71240z, October 27, 2014   

   • Brendan McLaughlin
   • Rb
   • 62 replies
   • 20.5k views
   • 
   • Nismospek
   • March 7, 2018

5. Supra 440cc Injector install question

   By HarveyZ, October 27, 2014
   • 4 replies
   • 1.8k views
   • 
   • HarveyZ
   • November 6, 2014

6. Boring plate

   By rjracin240, October 27, 2014
   • 1 reply
   • 866 views
   • 
   • Xnke
   • October 27, 2014

7. Where did all the power go?

   By dapiper, October 22, 2014
   • 9 replies
   • 2.3k views
   • 
   • madkaw
   • October 25, 2014

8. Replacing coolant lines!

   By konradlip, October 15, 2014   

   • coolant
   • hoses
   • (and 1 more)

     Tagged with:

     • coolant
     • hoses
     • lines
   • 2 replies
   • 1.3k views
   • 
   • konradlip
   • October 16, 2014

9. Mangoletsi Manifold

   By 150, October 13, 2014   

   • Mangoletsi
   • Manifold
   • (and 1 more)

     Tagged with:

     • Mangoletsi
     • Manifold
     • Weber
   • 10 replies
   • 4.5k views
   • 
   • Bob_H
   • October 30, 2014

10. Crank pully sync magnet placement wrong? and does IAT sensor go here?

    By lwrnclightner, October 12, 2014   

    • sds
    • 240sx throttle bddy
    • (and 3 more)

      Tagged with:

      • sds
      • 240sx throttle bddy
      • iat sensor
      • inlet air temp sensor
      • turbo
    • 6 replies
    • 2.3k views
    • 
    • lwrnclightner
    • November 3, 2014

11. Clearance questions. LD intake on gas engine.

    By tyler031734, October 1, 2014   

    • Any locals around Portland OR
    • 8 replies
    • 2.2k views
    • 
    • Xnke
    • October 6, 2014

12. Using an N42 intake and a 60mm 240 TB on an '83 280ZX? Need some help?

    By Mirage775, September 30, 2014
    • 8 replies
    • 1.7k views
    • 
    • Mirage775
    • October 2, 2014

13. "B" stamped cam but externally oiled?

    By Dwigley, September 30, 2014
    • 7 replies
    • 2.9k views
    • 
    • Tony D
    • October 1, 2014

14. Timing chain too tight??

    By 2eighTZ4me, September 27, 2014
    • 5 replies
    • 1.7k views
    • 
    • 2eighTZ4me
    • October 28, 2014

15. 82-83 ZX Rod Differences between NA and Turbo Engines?

    By Mirage775, September 23, 2014
    • 2 replies
    • 1k views
    • 
    • Mirage775
    • September 23, 2014

16. 280zxt engine harness question

    By TheDeadZed, September 20, 2014
    • 9 replies
    • 2.5k views
    • 
    • NewZed
    • September 27, 2014

17. Lost a gasket to my auto trans

    By BlueStag, September 19, 2014
    • 0 replies
    • 766 views
    • 
    • BlueStag
    • September 19, 2014

18. Twin cam head for the L6 from Derek at Datsunworks 1 2 3 4 73

    By Derek, September 19, 2014   

    • DOHC Head
    • 1.5k replies
    • 520k views
    • 
    • Ben280
    • July 9, 2025

19. Cometic MLS - copper coat or not....

    By 2eighTZ4me, September 18, 2014
    • 5 replies
    • 2.1k views
    • 
    • godzeerah
    • November 1, 2014

20. car wont rev past 3500rpm, 280ZX dizzy issues on SU carbs?

    By ol doc gully, September 18, 2014
    • 12 replies
    • 4k views
    • 
    • ol doc gully
    • September 24, 2014

21. Racing with a 3.2L NA Engine

    By gnosez, September 18, 2014
    • 11 replies
    • 4k views
    • 
    • josh817
    • September 22, 2014

22. Schneider valve springs.....diameter

    By 2eighTZ4me, September 16, 2014
    • 3 replies
    • 997 views
    • 
    • NewZed
    • September 16, 2014

23. '82 ZX N/A: Sluggish performance, tach needle jumping, and RPM surging beyond 5000. 1 2

    By Connor280ZX, September 16, 2014
    • 32 replies
    • 4.8k views
    • 
    • Connor280ZX
    • October 28, 2014

24. Pistons protrude from block - thicker gasket? 1 2

    By rick240zed, September 15, 2014
    • 20 replies
    • 6.5k views
    • 
    • Tony D
    • September 18, 2014

25. Rocker Arms - State of the situation 1 2

    By NewZed, September 14, 2014
    • 30 replies
    • 14.8k views
    • 
    • 280zex
    • June 8, 2015

26. Intake EGR Adapter

    By bens1088, September 13, 2014
    • 0 replies
    • 711 views
    • 
    • bens1088
    • September 13, 2014