MegaSquirt

1996 topics in this forum

1. MS3 Pro Install

   By tooquick260, December 25, 2015   

   • megasquirt
   • turbo
   • (and 8 more)

     Tagged with:

     • megasquirt
     • turbo
     • datsun
     • s15 speed
     • 240
     • 260
     • 280zx
     • 240z
     • 260z
     • z32
   • 1 reply
   • 2.6k views
   • 
   • tech9
   • July 27, 2016

3. Stock 280z running wasted spark on ms2

   By FlameShadow, July 3, 2016
   • 5 replies
   • 1.3k views
   • 
   • FlameShadow
   • July 7, 2016

4. Can't get stable Megasquirt idle & backfire (?) at TPS cut (280ZX N/A, fuel only)

   By Pepijn, June 25, 2016
   • 6 replies
   • 2.5k views
   • 
   • Chickenman
   • June 28, 2016

5. L28ET Swap Won't Crank Over

   By Crespo79, June 6, 2016
   • 6 replies
   • 1.5k views
   • 
   • Chickenman
   • June 8, 2016

6. Megasquirt with sbc tpi motor

   By Datsv8r, May 10, 2016
   • 1 reply
   • 1.3k views
   • 
   • Matt Cramer
   • May 13, 2016

7. Rotor phasing

   By annoyingorange, May 11, 2016
   • 4 replies
   • 1.6k views
   • 
   • NewZed
   • May 11, 2016

8. TPS reading correct

   By 98blackbell, January 18, 2016   

   • ms3pro
   • megasquirt
   • (and 4 more)

     Tagged with:

     • ms3pro
     • megasquirt
     • s30
     • 240z
     • 260
     • 280z
   • 6 replies
   • 3.7k views
   • 
   • 98blackbell
   • April 3, 2016

9. msqur.com - .msq tune viewing site 1 2

   By BLOZ UP, December 11, 2014
   • 23 replies
   • 4.5k views
   • 
   • BLOZ UP
   • April 3, 2016

10. Stock tach gauge wiring? Resistor needed? N/A 280ZX.

    By Manya, March 26, 2016
    • 2 replies
    • 1.9k views
    • 
    • Chris83zxt
    • March 30, 2016

11. No longer starting

    By Klmykvl, March 9, 2016
    • 7 replies
    • 1.3k views
    • 
    • skirkland1980
    • March 23, 2016

12. L28et megasquirt tuner in NJ??

    By konradlip, March 14, 2016
    • 0 replies
    • 888 views
    • 
    • konradlip
    • March 14, 2016

13. Megasquirt help in Sacramento Area

    By Klmykvl, March 2, 2016
    • 2 replies
    • 953 views
    • 
    • Klmykvl
    • March 12, 2016

14. Injector pwm setting for standard low impedance injectors 280zx?

    By Manya, March 10, 2016
    • 1 reply
    • 1.3k views
    • 
    • NewZed
    • March 10, 2016

15. RPM bouncing (3-500) in log, but drives ok

    By datsun74z_tn, March 6, 2016
    • 3 replies
    • 1k views
    • 
    • skirkland1980
    • March 8, 2016

16. Megasquirting an na 280zx. Changes to the pbc?

    By Manya, February 28, 2016
    • 3 replies
    • 1.1k views
    • 
    • Manya
    • February 29, 2016

17. 1st draft. wiring for L28-MS3pro

    By edwin, February 19, 2016
    • 10 replies
    • 4k views
    • 
    • Curtball
    • February 27, 2016

18. 240z tach driver

    By davek, February 17, 2016
    • 16 replies
    • 3.3k views
    • 
    • madkaw
    • February 25, 2016

19. MS3 / EDIS MSQ Needed

    By Scottie-GNZ, February 23, 2016
    • 0 replies
    • 971 views
    • 
    • Scottie-GNZ
    • February 23, 2016

20. MS #3 On Its Way

    By Tony D, April 16, 2015
    • 2 replies
    • 1.3k views
    • 
    • Bernardd
    • February 18, 2016

21. IAT install location L28ET

    By Klmykvl, September 10, 2015
    • 5 replies
    • 2.2k views
    • 
    • calpoly-z
    • February 16, 2016

22. Recommend a new laptop, or needing software.

    By xxjoeyxxeb, February 9, 2016
    • 7 replies
    • 2.1k views
    • 
    • madkaw
    • February 13, 2016

23. MS3X Throttle body/TPS options

    By Ben280, December 21, 2015
    • 4 replies
    • 1.6k views
    • 
    • FricFrac
    • February 2, 2016

24. High RPM Signal

    By seattlejester, March 9, 2014
    • 12 replies
    • 5.4k views
    • 
    • sabaozinhox
    • January 28, 2016

25. Bought a used Car with MS - 1 v3.0, need help identifying proto mess

    By tolerate, January 3, 2016   

    • proto
    • ms1
    • 9 replies
    • 1.5k views
    • 
    • tolerate
    • January 5, 2016

26. D14 injector Led solid when ignition is on

    By Klmykvl, January 2, 2016
    • 1 reply
    • 1.1k views
    • 
    • Matt Cramer
    • January 5, 2016