Fabrication / Welding

1330 topics in this forum

1. Sunroof, should I patch or cut?

   By voltron_boi, February 19, 2014
   • 6 replies
   • 1.9k views
   • 
   • fly-s30
   • April 3, 2014

3. A/C system from mazda miata into 240z

   By karl, March 6, 2007
   • 15 replies
   • 4k views
   • 
   • tube80z
   • March 29, 2014

4. Eastwood MIG-175

   By richie2619, March 12, 2014
   • 18 replies
   • 7.6k views
   • 
   • djbit
   • March 25, 2014

5. Stitch weld between rockers and floors?

   By savor, March 16, 2014
   • 6 replies
   • 2.6k views
   • 
   • RB26powered74zcar
   • March 19, 2014

6. Rear crossbar?

   By mr_han_solo, March 11, 2014
   • 8 replies
   • 2k views
   • 
   • johnc
   • March 12, 2014

7. Fox body mustang gas tank

   By richie2619, March 10, 2014
   • 5 replies
   • 3.9k views
   • 
   • richie2619
   • March 12, 2014

8. harbor freight wire welder? 1 2

   By ChrisZX2, July 16, 2013
   • 37 replies
   • 7.7k views
   • 
   • Tony D
   • March 11, 2014

9. DIY/homemade floor pans

   By surplus-addict, February 22, 2014
   • 16 replies
   • 23.4k views
   • 
   • SUNNY Z
   • March 10, 2014

10. Floor pans/Seat rails

    By grayson260z, March 3, 2014   

    • floor
    • pans
    • (and 4 more)

      Tagged with:

      • floor
      • pans
      • seat
      • rails
      • rust
      • remove
    • 5 replies
    • 2.5k views
    • 
    • grayson260z
    • March 4, 2014

11. Putting Battery in Passenger rear compartment 1 2

    By mr_han_solo, December 15, 2013
    • 20 replies
    • 6.6k views
    • 
    • Avernier
    • March 1, 2014

12. Good resource for auto fab

    By str8pipez, February 21, 2014
    • 3 replies
    • 1.2k views
    • 
    • OldAndyAndTheSea
    • February 22, 2014

13. Roll bar questions-yes I've searched plenty over the past two years

    By RebekahsZ, February 14, 2014
    • 18 replies
    • 2.9k views
    • 
    • RebekahsZ
    • February 18, 2014

14. Floor board/frame rail replacement question

    By fyanrudger, January 12, 2014
    • 18 replies
    • 2.7k views
    • 
    • WizardBlack
    • February 12, 2014

15. Alternate Custom Seat Bracket Option

    By fyanrudger, February 3, 2014
    • 5 replies
    • 1.8k views
    • 
    • WizardBlack
    • February 12, 2014

16. Proper location of roll bar's cross bar/harness bar

    By RebekahsZ, February 10, 2014
    • 8 replies
    • 6.9k views
    • 
    • WizardBlack
    • February 12, 2014

17. Custom intercoolers

    By thezguy, January 21, 2014
    • 9 replies
    • 2.3k views
    • 
    • SUNNY Z
    • February 11, 2014

18. 6an aluminum fuel rail tap

    By wickiewicked240z, February 3, 2014
    • 4 replies
    • 2.3k views
    • 
    • xero_xero
    • February 4, 2014

19. Trans adaptor l28 to chevy trans?

    By twoeightythreez, January 26, 2014
    • 2 replies
    • 1.5k views
    • 
    • xero_xero
    • February 3, 2014

20. Door bars that miss the window crank and door handle 1 2

    By RebekahsZ, January 12, 2014
    • 25 replies
    • 4.6k views
    • 
    • RebekahsZ
    • January 31, 2014

21. question about fabricating a manifold and coatings

    By FJ 280z, March 3, 2011
    • 15 replies
    • 4.8k views
    • 
    • BLOZ UP
    • January 17, 2014

22. looooooow budget rollcage 1 2

    By logan1, August 16, 2013
    • 32 replies
    • 8k views
    • 
    • johnc
    • January 11, 2014

23. Roll cage: has anyone been able to make a knee-bar that doesn't interfere with radio and heater controls?

    By RebekahsZ, December 28, 2013
    • 4 replies
    • 1.5k views
    • 
    • RebekahsZ
    • December 30, 2013

24. Center console shifter for Saginaw / Muncie / Toploader style sideshift transmissions

    By weedburner, December 24, 2013
    • 3 replies
    • 3.5k views
    • 
    • weedburner
    • December 25, 2013

25. Recessed engine mounting (into the firewall) 1 2

    By z1 zonly, June 16, 2012
    • 31 replies
    • 14.8k views
    • 
    • z1 zonly
    • December 17, 2013

26. custom fuel rail

    By winstonusmc, November 25, 2013
    • 4 replies
    • 2.1k views
    • 
    • winstonusmc
    • December 12, 2013